Vbar NEO non v-link freeze with BK 8002 servos (OptiPower BEC guard x2 work!!)

Vbar NEO non-vlink works with BK 8002HV servos if two OptiPower BEC guards are used with the Hobbywing 130A ESC to filter power to the Vbar remote satellite... Other BECs will be tested... Hercules BECs work without the need for a BEC guard....

---

Closed Caption:

okay Haley figures this is we're a SMO
my name is zero ongoing saga trying to
figure out the issues with these BK 800
two servos
Ryan has suggested that I try the
twentieth of power Dec guard
I went and as usual always tend to have
a habit of purchasing more than one
I'm think like it first off later on
Ryan suggested also that I try six volts
so just to show my settings right now 16
volts BK 800 two servos the BK Oh ones
to give yourselves
ok the 80 ones are fine around the 80
ones on my seven on
excuse me 707 70
all right remove the figures high torque
will be good for a bigger helicopter so
i moved the Alliance arose to my 570
they work fine with the b-bar nano and
external this is a non vlink v-bar nano
with the external satellite receiver
ok going to six volts you like go off
now watch the servos finger 6 volts
clean
hobbywing high voltage hundred 30 amp
with tenant bc internal straight to the
Nano and
both this lead and the SC lead both same
power to it
this is what I found out is his
suggestion to look into my phone down
was what about the apt to power bc guard
well its faults we're going to plug one
bc guard in want to prove a point here
new discovery at six bolts 1 b ec guard
works fine and eight volts
you need to sew her back up
ok
should be easy guard and the one of the
power leads to a matter which and worked
6 volts
now see what happens when we go up in
voltage
ok
doesn't go up until we slide the power
kind of the voltage to the ok
no enough so we were a small says hey
let's add another be easy
guard
ok
all right good to be easy guards
hobbywing tempt 8 volts verified pitch
pump setting 50 and it is so we have a
solution fellas and gals
yes by all these two all right up the
power b ec guard two of them takes two
if you have two leads coming from your b
ec will be testing it with the castle
I'll be testing it with the r JX it's a
40 mb c which I've already tested does
not work
stand alone the only bc so far that work
stand alone is this 10 amp Hercules b ec
this is the part number that i've tested
with my situation my situation is a
Barney OH external it's a non vlink it's
got an external satellite and it does
work
I choose not to run that because it adds
extra an extra component I don't have a
lot of room
I prefer the internal for the hobbywing
so if i choose to run the 802 sir
servos on my 572 these optical power
Dec guard devices clean the power up
enough to keep it from affecting the
external satellite and killing comms
communications all right
special thanks to ryan off for that
suggestion and X free 3d
I believe this answered his question
when I started out about dropping the
voltage
i'm correct or perhaps that was ryan up
ya know x freak 3d wanted me to check
the hobbywing a lower voltage
I went to six volts it didn't work i
went to 7.4 it didn't work and it ate it
doesn't work there is some sort of
correlation here because 1 b ec guard
works at a lower voltage in to bc guards
work at a higher voltage perhaps
somebody can make a device that does the
same thing as these B EC guards and
perhaps somebody already makes a device
that does the same thing as these two bc
guards but if you're running a high
voltage you know Cee Cee and you really
want to use you know
optimum voltage for your service speed
so these two work and there's the
packaging
ok and this works
all right that's two solutions so far
and i will be testing these to make sure
if they work with other becs as well
again the Hercules does work on its own
standalone castle
r JX hobby when do not so you got two
winners here when their chicken dinner
alright thanks Ellie freakers this is
we're a small signing off
cheers hope see a durga